Skip to content
OlingoPrint

Boxes and packaging: dielines, board, bleed and a file the printer can cut

What a dieline is, how to size a box to your product and the board, which panels print and which fold, and the PDF a Canadian packaging printer expects — with a 3D preview before you order.

Last updated:

  • Every design in many sizes
  • An editor made for phones

Packaging is the hardest thing a small business prints, for one reason: the file is not a flat page. It is a drawing of a box that has to be cut, creased, folded and glued, and every panel has to end up where you expected, with the logo the right way up. This guide explains the dieline, how to size a box, which board to pick and what the printer needs, so the first box that arrives is the one you designed.

What a dieline is

A dieline (also "die line" or "die cut template") is the flat outline of the box before it is folded, drawn in two kinds of lines:

  • Cut lines, usually solid: where the cutting die cuts through the board.
  • Crease or score lines, usually dashed: where the board is pressed so it folds cleanly.

Some templates add a third kind for perforations (tear strips) or glue areas. The dieline is placed in the file on its own layer, in a spot colour named something like "Dieline" or "CutContour", and set to overprint, so it sits on top of the artwork without knocking a hole in it. It is an instruction for the die maker and is never printed.

Most packaging printers will send you the dieline for the exact box style and size you order, as a PDF or an Illustrator file. The artwork is then placed on that template. If you design first and size later, the panels will not match and the printer sends the file back.

Box styles a small business uses

Style Short name How it closes Typical products
Straight tuck end STE tuck flaps at both ends, same side cosmetics, tea, soap, small electronics
Reverse tuck end RTE tuck flaps at both ends, opposite sides the same, slightly cheaper to make
Auto-lock bottom crash lock bottom locks itself when squeezed open heavier items: candles, jars, bottles
Mailer box RETT (roll end tuck top) a lid folded from the same sheet, locks with tabs shipping, subscription boxes, gifts
Sleeve – an open band around a tray or product soap, chocolate, gift sets
Pillow box – curved ends fold in small gifts, jewellery, favours

The tuck end carton is the box you know from a cosmetics shelf: cheapest, easiest to fill by hand, prints on paperboard. The auto-lock bottom costs a little more and holds weight without taping. The mailer box is the e-commerce box: corrugated board, strong enough to ship, with the inside printable for an unboxing moment. Canada Post's lettermail thickness limit (20 mm) decides whether a thin mailer ships as oversize lettermail or as a parcel, which is a large difference in price.

Sizing a box to the product

Box sizes are given as length × width × height of the inside, in that order, with the opening at the top. Three steps:

  1. Measure the product at its widest points. For a round jar, length and width are the diameter.
  2. Add clearance: 1/16 inch (1.5 mm) per side for a snug fit, 1/8 inch (3 mm) per side if the product goes in a bag or wrap first. Too snug and the box bulges and the tuck flaps will not close; too loose and the product rattles.
  3. Add the board: the inside dimension is what you specify, but the board folds inside the panel, so each inner dimension grows by about one board thickness. For 18 pt board (0.018 inch) that is small; for E-flute corrugated (about 1/16 inch) it matters.

A 4 × 4 × 2 inch candle, snug fit, in 18 pt board: specify an inside of about 4.125 × 4.125 × 2.125 inches. A printer's quote tool usually asks exactly for these three numbers plus the board, and generates the dieline from them. Canadian printers quote in inches or millimetres; both appear on most order forms, so pick one and stay with it.

Board and finish

Board Thickness Feel Use
SBS paperboard, 16 pt 0.016 in (~350 gsm) light carton light cosmetics, tea bags
SBS paperboard, 18 pt 0.018 in (~400 gsm) the standard folding carton cosmetics, food, candles
SBS paperboard, 24 pt 0.024 in (~500 gsm) rigid carton premium products, glass
Kraft board, 18–24 pt – brown, natural, matte handmade, organic, bakery
E-flute corrugated ~1/16 in thin corrugated, prints well mailer boxes, subscription boxes
B-flute corrugated ~1/8 in stronger, coarser print shipping heavier goods

SBS (solid bleached sulfate) is the white, smooth board that prints vivid colours. Kraft is unbleached and brown; white ink and black ink look best on it, and photos look muddy. Corrugated is for shipping; E-flute is the finest and the one that prints a logo cleanly. Finishes are the same as for cards: gloss or matte lamination, soft-touch, spot UV on a logo, foil. A laminate is worth it for anything handled a lot or stored in a bathroom or kitchen.

Artwork on a dieline: the rules

  • Bleed 0.125 inch outside every cut line. Backgrounds and photos extend past the cut, the same as a flyer.
  • The glue flap and tuck flaps print too. They are visible when the box is opened, and the glue flap edge shows at the seam. Carry the background colour onto them.
  • Keep text 0.125 inch away from creases, not just from cuts. A crease catches ink and distorts anything crossing it. Each panel is its own page in your head: a headline stays inside one panel.
  • Mind the orientation. On a flat dieline, two panels are upside down relative to the front. The 3D preview exists to catch exactly this.
  • Barcodes go on a flat panel, never across a fold, at least 1 inch wide, in 100% black on a white or very light background, and need a quiet zone around them.
  • Legal lines (ingredients, weight, address) are bilingual in Canada for most consumer products and have minimum sizes; 6 pt is the usual floor, 8 pt is safer on board, and food labelling regulations set their own minimum type heights.
  • Colours in CMYK, large solids in rich black, no RGB. On kraft, test a proof: every colour darkens.

The file the printer wants

One PDF, with:

  • the artwork in CMYK, 300 dpi images, text converted to outlines, on one layer;
  • the dieline on a separate layer, as a spot colour named "Dieline" or "CutContour", set to overprint, exactly as the printer's template;
  • 0.125 inch bleed, crop marks outside the bleed;
  • for a mailer box, the inside print as a second page if the inside is printed.

Before the full run, order a physical proof or a single sample. A screen cannot show you how the board folds, how the tuck closes or how kraft swallows a colour. A sample costs a few dollars and a week; a wrong run costs the whole order.

Doing all of this on your phone

OlingoPrint builds the dieline from your product's size and the board thickness, in the tuck end, auto-lock, mailer and sleeve styles, with bleed and the glue flap drawn. You put the artwork on each panel, then slide the box closed in 3D to see which panel ends up where and whether the logo faces the front. The export is a PDF with the cut and crease lines on their own layer in a spot colour, artwork in CMYK with text converted to outlines, which is the file packaging printers ask for. Ready designs for candles, clothing, baked goods and cosmetics are included. The free version adds a watermark; Pro removes it.

Send that PDF to the printer with the box size and board you chose, and ask for a sample first.

Frequently asked questions

What is a dieline?

A dieline is the flat drawing of a box before it is cut and folded: solid lines where the cutter cuts, dashed lines where the board is creased to fold. It is drawn in the file as a separate layer in a spot colour and is never printed; the artwork goes underneath it.

How do I size a box to my product?

Measure the product (length, width, height), add 1/16 to 1/8 inch (1.5–3 mm) of clearance per side so it slides in, then add the board thickness to the inside dimensions, because the board takes up space when folded. A 4 × 4 × 2 inch candle in 18 pt board needs an inside box of about 4.125 × 4.125 × 2.125 inches.

What is the most common box style for small products?

The straight tuck end (STE) and reverse tuck end (RTE) folding carton: a rectangular box with tuck flaps at both ends, used for cosmetics, candles, tea, soap, electronics accessories. For shipping, the mailer box (a roll end tuck top, or RETT) with its own locking lid.

Which board should I choose?

For folding cartons, SBS paperboard at 16–24 pt (roughly 350–500 gsm): 18 pt is the usual choice for cosmetics and food. For mailer boxes, E-flute corrugated (about 1/16 inch thick) prints well and protects the product. Kraft board gives a natural look and takes less ink.

Does a box need bleed?

Yes, 0.125 inch (3 mm) outside every cut line, and the artwork must also extend under the glue flap and the tuck flaps, which are visible when the box is opened. Keep text 0.125 inch inside each panel, away from the folds: the crease catches ink and a line of text across a fold always looks broken.

What file does a packaging printer want?

One PDF with the artwork in CMYK on one layer and the dieline on a separate layer in a spot colour named Dieline or CutContour, set to overprint, with 0.125 inch bleed and fonts converted to outlines. Most printers send you their dieline template for the exact box; the artwork is placed on it.

Can I design a box on my phone?

Yes. OlingoPrint builds the dieline from your product's size and the board thickness, lets you put the artwork on each panel, folds the box in 3D so you see which panel faces which way, and exports a PDF with the cut and crease lines on their own layer.